Chimney-Liner - Quattro-PLUS Flue Liner 904L Grade - Solid Fuel 250mm (10 inch)



Multi fuel flexible liner made from 904L grade stainless steel on both the inner and outer walls - 25 year manufacturers warranty with this product.
 

WARRANTY
904L Grade Flue Liner is warranted for 20 years (conditions apply)

APPLICATION
A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat, smokeless fuels.

CONSTRUCTION
The flue liner has a smooth inner liner made from 904L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 904L stainless steel and is 0.12mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a Quattro lock seal.

APPROVAL
Flue Liner is approved and listed by HETAS

INSTALLATION - CHECK LIST
1.Make sure the liner will go down the chimney (this can be done by pulling down a small section of the diameter liner you will be using)
2.Sweep your chimney.
3.Check you pot is in good condition, if you are NOT using a suspended cowl then remove the pot from the stack.

 

INSTALLATION
Flue Liner should always be fitted from the top.
Make sure the arrows are pointing upwards (gas flow).
Secure a piece of string (at least the same length as the Flue Liner to the Nose Cone (order separately).
Now attach the Nose Cone onto the end of the Flue Liner, again making sure the arrows on the Flue Liner are pointing away from the Nose Cone in a upward direction so when the liner is installed the arrows will be pointing to the top of the chimney
Pull the liner down the chimney using the string and at the same time have someone at the top of the chimney feeding the Flue Liner down, once the Flue Liner is fitted remove the Nose Cone.

MAINTENANCE
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Chimney Liner - Quattro-PLUS Flue Liner 904L Grade - Solid Fuel 150mm (6 inch)



Multi fuel flexible liner made from 904L grade stainless steel on both the inner and outer walls - 25 year manufacturers warranty with this product
 

 

WARRANTY
904L Grade Flue Liner is warranted for 20 years (conditions apply)

APPLICATION
A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat, smokeless fuels.

CONSTRUCTION
The flue liner has a smooth inner liner made from 904L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 904L stainless steel and is 0.12mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a quattrolock seal.

APPROVAL
Flue Liner is approved and listed by HETAS

INSTALLATION - CHECK LIST
1.Make sure the liner will go down the chimney (this can be done by pulling down a small section of the diameter liner you will be using)
2.Sweep your chimney.
3.Check you pot is in good condition, if you are NOT using a suspended cowl then remove the pot from the stack.

 

INSTALLATION
Flue Liner should always be fitted from the top.
Make sure the arrows are pointing upwards (gas flow).
Secure a piece of string (at least the same length as the Flue Liner to the Nose Cone (order separately).
Now attach the Nose Cone onto the end of the Flue Liner, again making sure the arrows on the Flue Liner are pointing away from the Nose Cone in a upward direction so when the liner is installed the arrows will be pointing to the top of the chimney
Pull the liner down the chimney using the string and at the same time have someone at the top of the chimney feeding the Flue Liner down, once the Flue Liner is fitted remove the Nose Cone.

MAINTENANCE
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Chimney (All Fuels) 5 inch 135º Tee diam 125



The 135Ëš Tee is used when you need a cleaning access at the base of the chimney. It is the first piece installed on the external wall and allows for ease cleaning of the flue. The 135Ëš Tee is shaped in such away that it does not restrict the flue gases.
This item comes with a 2 FREE Locking Bands.
 

APPLICATION
For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil boiler and any solid fuel appliances.

CONSTRUCTION
Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 128kgper cubic metre. All parts are fully welded.
Distance to combustibles is 60mm.

APPROVALS
KC is HETAS Approved and is CE marked.

Designation Number
EN1856-1 T600 N1 D V2 L50040 G60.

INSTALLATION
KC Twin Wall Insulated Chimney parts are secured together by using a Locking Band (supplied).
Make sure that you keep a distance of 60mm from the outside of the flue to any combustible material (wood, plaster board).

Flue Liners (Gas + Oil) - Flue Liner 316L for Gas and Oil (316L Grade)



Suitable for use on appliances fired by gas ( as specified by the fire manufacturer ), and oils up to 28 second.
 

APPLICATIONA single skin flexible flue liner suitable for relining within a masonry chimney. Suitable for use on appliances fired by gas ( as specified by the fire manufacturer ), and oils up to 28 second, and designed to accommodate temperatures not exceeding 260ËšC.

CONSTRUCTIONThe flue liner is manufactured from 316L grade stainless steel and is 0.10mm thick. The flue liner has five convoluteions between each seam. The Flue Liner seam is folded in three planes to give a TRIPLELOCK seal.

APPROVALTRIPLELOCK Flue Liner is Kitemarked to BS 715 and has been approved and tested to BS EN 1856:2

DESIGNATION NUMBERBS EN 1856:2 T250 N1 D V3 L50010 G

INSTALLATION - CHECK LIST1.Make sure the liner will go down the chimney (this can be done by pulling down a small section of the diameter liner you will be using)
2.Sweep your chimney.
3.Check you pot is in good condition, if you are NOT using a suspended cowl then remove the pot from the stack.

 

INSTALLATIONFlue Liner should always be fitted from the top.
Secure a piece of string (at least the same length as the Flue Liner to the Nose Cone (order separately).
Now attach the Nose Cone onto the end of the Flue Liner
Pull the liner down the chimney using the string and at the same time have someone at the top of the chimney feeding the Flue Liner down, once the Flue Liner is fitted remove the Nose Cone. If necessary cut the flue liner to length, and secure the liner at the top using the clamp plate. Ensure 75mm of the flue liner projects above the clamp plate so that the terminal can be located and secured.
Secure and seal the flue liner to a register plate, which closes off the appliance recess. Alternatively the end of the flue liner can be sealed into flue pipe or a Flue Gas Collector or Flue Box.
Terminate the flue liner by securley fitting the terminal to the projecting section of flue liner. Apply a suitable cement as a seal and weather proof render.

MAINTENANCEIt is recommended that chimneys serving gas and oil appliances be swept and maintained as frequently as necessary but at least once a year.

Chimney Liner - Installation Pack No (702)



Installation Pack No. 2, ALL YOU NEED IN ONE BOX FOR USE WITH 180mm diameter multifuel flex.
 

APPLICATIONUse this pack when you want to remove the existing chimney pot, or the chimney does not have a pot.

PACK CONTAINS1 x Top Plate - diam180mm
1 x Top Clamp - diam180mm
1 x Top Insert - diam180mm
1 x Nose Cone - diam180mm
1 x Adaptor to Black Pipe or Single Wall Flue - diam180mm
1 x Chimney Notice Plate
1 x Rain Cap - diam180mm

Chimney Cowls - Junior Birdguard (terracotta) - strap fix



Designed to prevent birds, vermin and leaves entering used (for oil or gas appliances) or unused chimney flues. This product provides good ventilation and gives protection against wind and rain. Fits flue sizes 125-250mm internal diameter. This product is secured by a strap fixing. Steel finish.

Chimney-Liner - DS Flue Liner 316L/904L Grade - Solid Fuel 150mm (6 inch)



Multi fuel flexible liner made from 904L grade stainless steel on the inner and 316L grade stainless steel on the outer walls, both the smooth inner liner and convoluted outer skin being 0.12mm thick. - 15 year manufacturers warranty with this product.
 

APPLICATION
A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat, some smokeless fuels.

CONSTRUCTION
The flue liner has a smooth inner liner made from 904L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.12mm thick. The Flue Liner is constructed from two strips of steel and the seam is folded in three planes to give a triplelock seal.

APPROVAL
Flue Liner is approved and listed by HETAS

INSTALLATION - CHECK LIST
1.Make sure the liner will go down the chimney (this can be done by pulling down a small section of the diameter liner you will be using)
2.Sweep your chimney.
3.Check you pot is in good condition, if you are NOT using a suspended cowl then remove the pot from the stack.

INSTALLATION
Flue Liner should always be fitted from the top.
Make sure the arrows are pointing upwards (gas flow).
Secure a piece of string (at least the same length as the Flue Liner to the Nose Cone (order separately).
Now attach the Nose Cone onto the end of the Flue Liner, again making sure the arrows on the Flue Liner are pointing away from the Nose Cone in a upward direction so when the liner is installed the arrows will be pointing to the top of the chimney
Pull the liner down the chimney using the string and at the same time have someone at the top of the chimney feeding the Flue Liner down, once the Flue Liner is fitted remove the Nose Cone.

MAINTENANCE
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.