7 inch Flue Liner - Rain Cap




Provides rain protection at the top of the stack.

APPLICATION
Provides rain protection at the top of the stack.

INSTALLATION
Terminal slides over the top of the liner and can be screwed into place with self tapping screws (not supplied) or alternatively can be cemented in to place at the top of the stack.
MAINTENANCE
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Proline - Brown Fire Basket - Ø39x31cm Faux Leather



Elegant firewood basket in imitated leather. The white seams gives a constrast to the leather, and provides the basket with an eye catching look. In additon to being useful for firewood, they are decorative and functional. This makes the baskets ideal for storing magazines, newspapers or childrens toys.

Increasing Flue Adaptor 125 Rigid to 150 Flex



A metal connector which connects the flexible chimney liner (one diameter size bigger - ie. 6 inch (150mm)) to single wall pipe at the base of the stack.

APPLICATION
Connects 150mm (6 inch) Flue Liner to 125mm (5 inch) Black Pipe / Vitreous Enamel / 1mm Stainless / Single Wall flue at the bottom of the chimney stack.
HETAS recommend that if you are burning wood then you should increase the size of the flue liner by 25mm from the appliances spigot size.
This is due to the amount of condensates that can be produced from burning unseasoned wood.

CONSTRUCTION
Made from 316 grade stainless steel, it has integral drain hole to let the condensates flow back into the flue.

INSTALLATION - CHECK LIST
1.Make sure the liner will go down the chimney (this can be done by pulling down a small section of the diameter liner you will be using)
2.Sweep your chimney.
3.Check you pot is in good condition, if you are NOT using a suspended cowl then remove the pot from the stack.

INSTALLATION
Flue Liner should always be fitted from the top.
Make sure the arrows are pointing upwards (gas flow).
Secure a piece of string (at least the same length as the Flue Liner to the Nose Cone (order separately).
Now attach the Nose Cone onto the end of the Flue Liner, again making sure the arrows on the Flue Liner are pointing away from the Nose Cone in a upward direction so when the liner is installed the arrows will be pointing to the top of the chimney
Pull the liner down the chimney using the string and at the same time have someone at the top of the chimney feeding the Flue Liner down, once the Flue Liner is fitted remove the Nose Cone.

MAINTENANCE
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Asgard 7 SK - DEFRA Black



DEFRA Approved Stoves for Smoke Controlled Stove Areas
Smoke-Controlled Stoves are DEFRA approved for use in smoke exempt urban, town and city zones.

An effective and functional convection stove covered with decorative soapstone, which gives a beautiful contrast to the black surfaces. Soapstone has a special ability to absorb and maintain heat.

Fire Rope - per metre 12mm Ø



Glass fibre woven Stove Rope is suitable for stoves and is supplied by the metre.

APPLICATION
Fire Rope is suitable for doors and lids on solid fuel stoves and boilers

CONSTRUCTION
Fire Rope is manufactered from woven glass fibres.

INSTALLATION
Clean away any old rope and remove and loose metal from the locating channel. Apply Fire Rope Adhesive following instructions on the container. Press Fire Rope firmly into channel, then cut Fire Rope with scissors to finish with an end to end butt joint. Allow fifteen minutes before closing doors.

Register Plate (K) - 180/200mm Hole 900mm x 600mm - 2 Access Holes




Register Plates are used to seal off the base of the chimney.
This Register Plate is 900mm x 600mm
It has TWO access holes.
It is suitable for 180mm and 200mm (7 and 8 inch) Black Stove Pipe.
DO NOT USE THIS REGISTER PLATE IF YOU ARE USING VERMICULITE TO INSULATE YOUR FLUE.

APPLICATIONUse to seal off the base of the chimney (This Register Plate can be cut on site to fit the base size of your chimney stack). The Register Plate will support vermiculite and stop any debris from within the chimney stack coming down the chimney and hitting your stove.

CONSTRUCTIONThe Register Plate and the Supporting Brackets are made from 1.5mm thick galvanised steel. The Register Plate can be sprayed to match the colour of your stove pipe. This Register Plate has a special adapter suitable for installations which use either 180mm or 200mm diameter flue pipes.

INSTALLATIONThe four supporting brackets should be cut to the length and width of the base of your chimney stack. Drill a number of holes in the brackets. Now screw them into the brickwork. Cut the Register Plate to the correct size, taking care that the pipe hole lies vertically above the Black Stove Pipe. Drop the Register Plate onto the supporting brackets. Now seal any gaps between the brickwork and the brackets / plate using Fire Cement or High Temperature Sealant. For 150mm diameter installations simply remove the centre cover ring by unscrewing the two retaining screws.

MAINTENANCEIt is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year. At the same time remove the Register Plates inspection hole cover plate(s) and hoover / sweep any debris that has fallen.
DO NOT REMOVE COVER PLATES IF VERMICULITE HAS BEEN INSTALLED AS ADDED INSULATION.

POD Five - 9 kW Stove



The Pod Five has a steel body giving a maximum of 13kw of heat with a nominal output of 9kw. A contemporary design with a large ceramic glass window gives an excellent view of the fire, the stove also has a convenient log storage space under the fire box the stove is available in matt grey. Internally it’s fully lined with firebricks.

The Pod Five is certified to BS EN13240 and comes with a 2 year warranty.

Proline - Black Fire Basket - Ø39x31cm PET



In additon to being useful for firewood, they are decorative and functional. This makes the felt baskets ideal for storing magazines, newspapers or childrens toys.

PET firewood baskets are made from recycled bottles.