Chimney-Liner - 150mm (6 inch) Increasing Flue Adaptor 125 Rigid to 150 Flex

 

 

A metal connector which connects the flexible chimney liner (one diameter size bigger - ie. 6 inch (150mm)) to single wall pipe at the base of the stack.

APPLICATION
Connects 150mm (6 inch) Flue Liner to 125mm (5 inch) Black Pipe / Vitreous Enamel / 1mm Stainless / Single Wall flue at the bottom of the chimney stack.
HETAS recommend that if you are burning wood then you should increase the size of the flue liner by 25mm from the appliances spigot size.
This is due to the amount of condensates that can be produced from burning unseasoned wood.
 

CONSTRUCTION
Made from 316 grade stainless steel, it has integral drain hole to let the condensates flow back into the flue.
 

INSTALLATION - CHECK LIST
1.Make sure the liner will go down the chimney (this can be done by pulling down a small section of the diameter liner you will be using)
2.Sweep your chimney.
3.Check you pot is in good condition, if you are NOT using a suspended cowl then remove the pot from the stack.

INSTALLATION
Flue Liner should always be fitted from the top.
Make sure the arrows are pointing upwards (gas flow).
Secure a piece of string (at least the same length as the Flue Liner to the Nose Cone (order separately).
Now attach the Nose Cone onto the end of the Flue Liner, again making sure the arrows on the Flue Liner are pointing away from the Nose Cone in a upward direction so when the liner is installed the arrows will be pointing to the top of the chimney
Pull the liner down the chimney using the string and at the same time have someone at the top of the chimney feeding the Flue Liner down, once the Flue Liner is fitted remove the Nose Cone.

MAINTENANCE
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

After Care Products Stove Thermometer



SAVE MONEY WITH A STOVE THERMOMETER Ensure your stove is operating at the correct temperature by using this magnetic stove thermometer that attaches to your black stove pipe.
If your stove is too cold then creosote deposits will form, if its too hot then you are wasting energy.

CONSTRUCTION
The Stove Thermometer is 2.5 inch Diameter (63mm). Its magnetic so attaches just above your stove on the Black Stove Pipe.

INSTALLATION
The stove thermometer attaches magnetically, directly to the metal flue pipe. Optimal location is at eye level, no less than 300mm (12 inches) above the top of the stove, where you can easily see it in the room.

Chimney (All Fuels) 5 inch Gas Cowl Ø 130



The Gas Cowl fits to the top of the flue system to stop any water coming down the flue. The protective shroud stops prevailing winds from effecting the flue. Ideal for use on gas installations.

A Locking Band is required to secure this part.

APPLICATION
For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil boiler, condensing boilers and any solid fuel appliances.

CONSTRUCTION
Outer skin is made from 304 grade stainless steel and is 0.5mm thick. Inner skin is made from 316 grade stainless steel and is 0.5mm thick. Insulation is compressed rockwool which is injected into the flue giving a density of 180kg/m³. All parts are fully welded – making DT suitable for condensing appliances.
Distance to combustibles is 50mm.

APPROVALS
DT is HETAS Approved and is CE marked.

Designation Number is EN1856-1 T600 N1 D V2 L50050 G50.

INSTALLATION
DT Twin Wall Insulated Chimney has a simple twist fit joint system, this is then secured by using a Locking Band - the simplest and strongest construction system on the market today.
Make sure that you keep a distance of 50mm from the outside of the flue to any combustible material (wood, plaster board). This distance is only for DT, other flues on the market may have distance of 60mm or more (this is because of the quality of the product) – please ask your supplier.

Aduro Easy Fire Starters tubes of 100


For safe and easy ignition of barbeques and wood stoves without any odours. Perfect for use in the home, when camping or hiking.

Place 2-3 firestarters between the logs or coal and light the corner of each sealed firestarter - the foil packaging will act as wick. The firestarters will burn for 7-10 minutes without giving off smoke or odours.
Unlimited durability.
Keep out of the reach of children.

Quattro-PLUS Flue Liner 904L Grade - Solid Fuel 180mm (7 inch)



Multi fuel flexible liner made from 904L grade stainless steel on both the inner and outer walls - 20 year manufacturers warranty with this product

WARRANTY
904L Grade Flue Liner is warranted for 20 years (conditions apply)

APPLICATION
A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat, smokeless fuels.

CONSTRUCTION
The flue liner has a smooth inner liner made from 904L grade stainless steel and is 0.12mm thick. The flue liner has a convoluted outer skin made from 904L stainless steel and is 0.12mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a quattrolock seal.

APPROVAL
Flue Liner is approved and listed by HETAS

INSTALLATION - CHECK LIST
1.Make sure the liner will go down the chimney (this can be done by pulling down a small section of the diameter liner you will be using)
2.Sweep your chimney.
3.Check you pot is in good condition, if you are NOT using a suspended cowl then remove the pot from the stack.

INSTALLATION
Flue Liner should always be fitted from the top.
Make sure the arrows are pointing upwards (gas flow).
Secure a piece of string (at least the same length as the Flue Liner to the Nose Cone (order separately).
Now attach the Nose Cone onto the end of the Flue Liner, again making sure the arrows on the Flue Liner are pointing away from the Nose Cone in a upward direction so when the liner is installed the arrows will be pointing to the top of the chimney
Pull the liner down the chimney using the string and at the same time have someone at the top of the chimney feeding the Flue Liner down, once the Flue Liner is fitted remove the Nose Cone.

MAINTENANCE
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Wall Support Plate and 2 Support Brackets


The Wall Support Plate with Straight Pipe and 2 Wall Support Brackets is used at the base of an external stack to support the weight of the chimney.

APPLICATION
For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil boiler, condensing boilers and any solid fuel appliances.

CONSTRUCTION
Outer skin is made from 304 grade stainless steel and is 0.5mm thick. Inner skin is made from 316 grade stainless steel and is 0.5mm thick. Insulation is compressed rockwool which is injected into the flue giving a density of 180kg/m³. All parts are fully welded – making DT suitable for condensing appliances.
Distance to combustibles is 50mm.

APPROVALS
DT is HETAS Approved and is CE marked.

Designation Number is EN1856-1 T600 N1 D V2 L50050 G50.

INSTALLATION
DT Twin Wall Insulated Chimney has a simple twist fit joint system, this is then secured by using a Locking Band - the simplest and strongest construction system on the market today.
Make sure that you keep a distance of 50mm from the outside of the flue to any combustible material (wood, plaster board). This distance is only for DT, other flues on the market may have distance of 60mm or more (this is because of the quality of the product) – please ask your supplier.

POD Eight - 7 kW



The Pod Eight has a steel body giving a maximum of 10kw of heat with a nominal output of 7kw. A contemporary design with a large ceramic glass front and side windows giving an excellent view of the fire from three sides, the stove also has a convenient log storage space under the fire box. The stove is available in matt black. Internally it’s fully lined with firebricks.

The Pod Eight is certified to BS EN13240 and comes with a 2 year warranty.

Gloss Black Enamel Pipe 90° Elbow with Door

 

90° elbow measured from the vertical - with access door for sweeping. This should only be used as the first piece when installing from the rear of an appliance.
 

APPLICATION
Suitable for gas, oil and solid fuel appliances with temperatures up to 750 degrees C.
Stove pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.
Black stove pipe should NOT be used to pass through ceilings or wall.

CONSTRUCTION
Black stove pipe is a single skin flue system manufactured in zero carbon steel with vitreous enamel coating in a matt black finish.
Suitable for gas, oil and solid fuel appliances with temperatures up to 750 degrees C

INSTALLATION
You should not install a piece of Vitreous Enamel Stove Pipe within 3 times the diameter of the flue from combustible material, e.g. wood, plaster boards, etc.
A 5 inch (125mm) diameter piece of Vitreous Enamel Stove Pipe should be 15 inches (375mm) away from combustible materials.
When installing make sure Vitreous Enamel Stove Pipe is installed the correct way up - the smaller diameter should always be pointing downward.
This is because all the condensates will stay within the flue system and not pass to the outside of Vitreous Enamel Stove Pipe.
Each joint should be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.

MAINTENANCE
You should make provision for inspecting and cleaning the chimney. This is particularly important on solid fuel applications.
You can acheive this by installing a Vitreous Enamel pipe with an access door.
It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

POD One - 5 kW


The Pod One is a multi-fuel stove with an efficient dual layer steel body convection system giving a maximum of 9kw of radiant heat with a nominal output of 6kw. A contemporary design with a large ceramic glass window gives an excellent view of the fire, the stove is available in matt grey. Internally it’s fully lined with firebricks.

The Pod One is certified to BS EN13240 and comes with a 2 year warranty.